TCA Issues with the FSLabs v.5.0.1.160 #481300

Print Edit

Dear Support,

 

I am in trouble with the TCA Quadrant. First of all, the last Version, which work properly is v5.1.0.126. Because I want to buy your new product, I am in Trouble with the new update since v.5.0.1.151… First: I read some similar Problems in the Forum, but it’s not the same. All Solutions provided there are not working for me.  

 

 

Whats the Problem?

 

Even, when I start the Airbus (saved in Cold & Dark Mode), this Buttons on my TCA-Quadrant doesn’t work:

 

• Engine Selector 1 and 2
• Enginge Mode Selector
• Parking Brake
• Rudder Trim
• Gear

 

This functions works:

• Flaps
• Speed Brakes
• Throttles
• Sidestick (all Axis)

 

 

 

I used the new Firmware from Thrustmaster (1.57 for the Quadrant).

 

 

Workaround

 

All (!) Buttons, decribed above, works fine, when I reconfigure via the FSLabs-Input-Commants only one function, which is not working, e.g. the Parking Brake. I open the Input Event Keys, the ThrustMaster TCA Quadrant and set the ParkBrake with the same key, listet into the Buttons Assignment List (Change -> Switch the TCA-Parking Brake -> Close). That’s all.

 

After this Setting up only one (!) button, all the other Buttons (Selector 1+2, Mode Selector, Rudder Trim, Gear and .. of Course, the Parking Brake) work properly.

 

 

What else I noticed

 

When I delete the „FSL_A320X_Kbd“-File, start the Simulator and load FSLabs, I confirm the two Dialogs. In this session (and only in this one!) the keys works perfect! When I close the Simulator and start it again, I have the same issues described above.

 

 

What I have done to fix this issue on my System

 

• Uninstall FSLabs (and Restart Computer)
• Delete all FSLabs Folders
• Install it again (and Restart Computer)
• Confirm the TCA-Configurations (one for Stick, one for Qudarant)

 

 

My System:

• P3Dv5.1 with the actual Hotfix
• I9-9990K, 32GB, GTX2080TI, 1TB SDD for OS, 1TB SDD for P3D
• FSLabs v.5.1.0.160 (installed in add-on-folder, „Documents“ in a separate (other) folder)
• SideStick-Firmware: v1.06, Qudrant-Firmare: v1.57. All Buttons/Controls works proberly in the Control Panel.

 

 

My Profile (for identification purposes):

 

 

I used the Forum, but nobody gave an answer about my Problems. So I try to use the support-mail .

 

Are you able to help me?

 

 

Best regards

Thomas   

 

 

 

 

Hi Support,

 

sorry, this is a big pain for me, because I finally have a stable simulator. I will switch back to v.5.0.1.126, if there is no other possibility.

 

What I have done is, to exclude all add-ons out of my sim via SimStarter NG. But this is also not working. What is funny: If I reconfigure only one (!) function (e.g. parking-brake) via FSLabs-Keyassignments, all the other buttons works. But that's annoying, then I'd rather do without new functions.

 

Best regards

Thomas 

 

 

 

Hi FSLabs,

 

Thanks for your email. Is there a list of which hardware switches can be mapped to which function in the simulator via FSUIPC? I have the full version of FSUIPC.

 

F.e.: the Parking Brake is assigned to “CTRL+.” – but I don’ know, if there are (separate) functions for “Parking-Brake-Set” and “Parking-Brake-Released”?

 

Best regards

Thomas  

 

 

Dear Support,

 

I have found a solution, which works with me. I am using the tool “SimStarter NG”, but it seems, that this is the problem. If I start P3D without this tool and load the FSLab-Aircraft, all buttons are working.

 

Thanks for your support. You can close the ticket.

 

Best regards
Thomas  

 

 

 

Hi FSLabs,

 

Thanks for your email. Is there a list of which hardware switches can be mapped to which function in the simulator via FSUIPC? I have the full version of FSUIPC.

 

F.e.: the Parking Brake is assigned to “CTRL+.” – but I don’ know, if there are (separate) functions for “Parking-Brake-Set” and “Parking-Brake-Released”?

 

Best regards

Thomas  

 

 

sorry for not updating you in this issue. I think this was not the Simstarter, it was a problem with using the ´default´ aircraft. I know, that it is recommened not to use FSLabs as a default aircraft, but it works for a long time.

Last weekend I tried several SimStarts, but when I unchecked in the start menu of p3d, that fslab isn‘t the default aircraft and after reloading from a standard-aircraft the fslabs, all functions are working properly. 

Now it works. And - believe me - I never will set up a fslab aircraft as a default aircraft :-) 

Best regards 

Thomas

Am 31.05.2021 um 16:46 schrieb FSLabs Support Help Desk :